Are not how do you hook up water to refrigerator apologise, but

phrase and

Imagine the convenience of having cold water or ice cubes any time you want them - no more filling up pitchers to keep in the refrigerator or waiting for ice cube trays to freeze. But once you've bought a refrigerator with a cold water dispenser and automatic ice maker, you'll still need a way to get water into it. It takes patience, but you can hook a water line up to your refrigerator on your own. Here's how [sources: Family Handyman , Whirlpool ]. Shut off the water supply.

Attach one end of the copper tubing to the refrigerator's water pipe, using a nut and ferrule.

congratulate, you were

Important: Make sure you leave extra tubing coiled behind the refrigerator, so you can move the refrigerator when necessary. Cut the cold water line under the sink or in the basement and attach a copper T-fitting.

authoritative answer

Attach a water valve to the T-fitting. This will control the water flow and water pressure to the refrigerator.

Be sure to put a gasket seal between the valve and the T-fitting. Attach the free end of the copper tubing to the valve.

topic Let's try

She is currently an editor at a major publishing company, where she works on various trade journals. Gomez also spent many years working as a newspaper reporter. She holds a bachelor's degree in journalism from Northeastern University.

How do you hook up water to refrigerator

By Cynthia Gomez. Hunker may earn compensation through affiliate links in this story.

can not take

Refrigerators with ice makers and water dispensers require a water line connection. Share this article.

Dec 10,   A refrigerator with an automated ice maker and a built-in water dispenser does absolutely nothing if you do not have a water line to connect to it. Many homes have a refrigerator water supply line. Hooking your refrigerator to your water valve is a simple, do-it-yourself project requiring few materials and tools. You'll need quarter-inch copper tubing that measures the length between your wall hookup and the hookup location on the back of your refrigerator, plus about 7 feet (to allow for moving the fridge). With the refrigerator out of its hole, go ahead and proceed to testing. Slowly open up the shutoff valve if you used the "under counter" method to connect it, or in my case, the main water valve and verify to make sure there aren't any leaks on the main water line. Then open up the valve for the fridge connection and do the same thing.

Cynthia Gomez. Another good alternative would be to use a braided stainless steel line, but they are double the price.

opinion you are

Whenever installing plastic pipe with compression fittings such as these, you always want to use plastic ferrules. The ferrule, AKA sleeve or olive, is the part the compresses on to the pipe which makes for a leak free joint.

for council how

If you use a brass ferrule, you run the chance of it cutting thru the pipe and causing the fitting to leak, this is where most DIYers make a mistake that could potentially lead to a disaster.

Another thing to keep in mind is using a brass sleeve inside the pipe.

good idea Quite

However, if you feel like trying it out, I do suggest watching this video right here as it gives easy step-by-step instructions on how to properly solder a copper pipe. However, these have a tendency to leak from the rubber joint after a while and are an accident waiting to happen, so I suggest you stay away from them even if they are tempting.

Now onto the tools.

opinion you

If you decide to solder it instead, I suggest getting an all-in-one soldering kit like this as they are a lot cheaper and give the same results. If this is the case, you might not need to shut off the main water valve to the house to install your tap.

Installing a refrigerator water line will open up a well of fresh water and ice that you and your family can easily enjoy. Connecting a water line to your refrigerator will provide it with the water necessary to make ice and dispense filtered water. Of course, if your refrigerator doesn't have an ice maker or water dispenser, or if it has one or both features but you prefer not to use them. Required Tools for this refrigerator water line project. Have the necessary tools for this refrigerator water line DIY project lined up before you start-you'll save time and frustration. Soldering torch; Tape measure; Tube cutter; You may also need a drill and a 1/2-in. bit if you need to run the water line through cabinets, as shown jankossencontemporary.com: The Family Handyman. Mar 12,   When you are setting up your Frigidaire refrigerator in your kitchen for the first time, you must connect a cold water line to your refrigerator using a flexible copper tube. The copper tubing is used as a water line that you can connect to the water inlet valve located on the back of your refrigerator. The water line must be properly connected.

Whenever drilling thru a floor, make absolutely sure the path is clear and that no electrical wires, pipes or vents are in the way or you could damage them and end up needing to called a contractor to get it fixed. So now that your water line is empty, start off by marking your pipe where it needs to be cut, and cut it using the pipe cutter.

Installing a push fitting like this is super easy but there are some steps to follow in order to make a proper connection.

I don't want an ice maker so do I have to buy the water line if I don't need or want hook - Learn about Smart Choice - Stainless-Steel Refrigerator Waterline Kit Required for Hook-Up - Silver with 7 Answers - Best Buy/5. But once you've bought a refrigerator with a cold water dispenser and automatic ice maker, you'll still need a way to get water into it. It takes patience, but you can hook a water line up to your refrigerator on your own. Here's how [sources: Family Handyman, Whirlpool].

Sharkbites require that the outside of the pipe is deburred before insertion. You could either use your Sharkbite deburring tool or just a flat file.

At this stage, I always like deburring the inside of the pipe as well to prevent turbulence and restriction.

Something else to keep in mind is marking the proper insertion depth to make sure it goes in all the way. You could use your Sharkbite deburring tool which also serves as a depth gauge or you could use this chart and mark it manually.



Facebook twitter google_plus reddit linkedin

0 thoughts on “How do you hook up water to refrigerator

Leave a Reply

Your email address will not be published. Required fields are marked *